For Sale Infors HT Multitron Refrigerated/Humidity Triple Incubator Shaker

Internal part number SM100116-RH

• Fully Functional
• Serviced & in Stock
• Good cosmetic condition
• Multiple incubators on hand
• Technical sales consultation available
• 45 DAYS INTERNATIONAL WARRANTY
• Includes remote instrument setup and training session  

•  The extra maintenance we perform in-house (in addition to testing steps):
• Chambers cleaned thoroughly
• Tested with NIST Traceable Calibrated probes
• Replace bearings in all three shakers (new)
• Replace the belts in all three shakers (new)
• Blue Sticky Mats in all three shakers (new)

This service adds between 25 to 35 hours of technical labor and is included at no charge

Predecessor to Multitron Pro

Here is what you will receive:

• Infors HT Multitron HT Triple Stack Incubator Shaker
• Multitron Sticky Mat Trays (QTY:3)
• Standard power cables (Qty: 3)

Infors HT Multitron Triple Incubator Shaker Configuration:

• Capacity: approx 200 Liters Per Chamber
• Interior Dimensions: 390 x 925 x 550 mm per chamber
• Standard parameters: temperature, rotation speed, timer
• Optional included parameters: cooling, humidification
• Rotation speed: 20-400 min^-1 depending on load and stacking; max. deviation: 1% with maximum speed of rotation
• Shaking throw: 25 mm
• Allowed loading (incl. tray) with 25 mm throw diameter: up to 350 rpm approx.: 9 – 19 kg; above 350 rpm approx.: 12 – 16 kg
• Temperature range: approx. 15 DegC below AT (but not under 4 DegC) up to 65 DegC
• Humidity Control range: 20 ... 85% rH in 1% rH increments
• Operating method: flash vaporization, pressureless
• Max. temperature with humidification: 40 DegC
• Water inlet pressure: pressureless (Direct steam humidification)
• Steam pressure extern: 1.5 – 2.0 bar (External steam humidification)
• Power supply: 115V, 60Hz 
• Weight: appr.400kg

Customizations are available to fit this instrument to your application (please inquire for pricing and availability):

• Central cooling for supply of up to 3 decks
• Side cooling for individual supply to a specific deck
• Units with different throw options are available: 25 mm, 50 mm
• Units with external & direct steam humidification: external water reservoir or internal water bath
• on hand that can be installed per request:

  • Universal trays with threaded holes, to accept flask clamps etc which are screwed into place
  • Tables with adhesive matting (sticky stuff) for any item with a flat base
  • Special holder for microtitre and deep-well plates.
  • Retaining clamps and holders
  • Test tube racks

Testing performed by our in-house service team:

• We ensure the instrument powers on smoothly without errors.
• We verify the precision and stability of temperature control.
• Test the cooling performance to ensure the set temperature is achieved and maintained.
• Verify the uniformity of temperature distribution throughout the unit.
• We evaluate the humidity control system for accuracy and stability.
• We test the humidification system to maintain the desired humidity levels.
• We assess the performance and consistency of orbital shaking.
• We validate the timer settings for accurate duration control.
• We test the alert system for temperature and shaking deviations.
• We verify sensors and system controls.
• We evaluate the functionality of the interface.
• We conduct a comprehensive assessment of the incubator shaker's operational functionality.

Instrument Overview:

• The Infors HT Multitron Triple Incubator Shaker provides precise temperature, humidity, and orbital shaking control.
• It has a spacious interior with adjustable shelves and can accommodate a wide range of flasks, tubes, and plates.
• The intuitive interface allows for easy programming and monitoring of parameters.
• Its triple stack design maximizes lab space efficiency without compromising performance.
• With its reliable and consistent operation, the Infors HT Multitron Triple Incubator Shaker is ideal for various research and bioprocessing tasks.

Instrument Application: 

• Cell culture
• Microbial culture
• Protein expression
• Molecular biology
• Enzyme studies
• Fermentation

The Key Features:

• Precise control of temperature, humidity, shaking
• Spacious interior, adjustable shelves
• Intuitive interface
• Triple stack design for efficiency
• Reliable for research, bioprocessing

Additional Technical Info:

Why do so many customers choose to order floor shakers from us?

They want to ensure the orbital shaking mechanism has been thoroughly tested under real load to confirm amplitude consistency and RPM stability across the entire platform, not just idled or spun unloaded.

They want to confirm that eccentric drive assemblies, belts, and counterbalance systems have new belts and bearings and are tested at maximum speed, preventing premature bearing failure or platform resonance.

They want to ensure the chamber has been disassembled and scrubbed down to ensure no spills or broken glassware is left behind to cause issues later on.

They want assurance that door seals, gaskets, and latch sensors are intact and pressure-tested, which is critical for stable thermal and gas environments in regulated applications.

They want to ensure programmable ramping, timing, and start/stop profiles are executed without error and validated through long-duration test cycles to expose hidden firmware faults or memory corruption.

They want to ensure that the temperature is not only accurate and tested against a NIST traceable probe but also proven to be stable over extended periods of time.

They want to ensure that onboard CO₂ and/or humidity regulation (if equipped) have been calibrated and verified using NIST traceable calibrated equipment, not guessed or assumed functional.

They want to ensure the refrigerant has not leaked out of the cooling system, resulting in low efficiency or a non-working system.

They want to ensure that the pumping efficiency of the cooling system has been assessed to ensure the reliability of the refrigeration system that runs the cooling or dehumidification systems.

They want to know if the humidification system has been inspected and if the ultrasonic generators have been tested for proper output.

Our Advantage

• We have experience servicing and repairing these instruments.
• This instrument goes through all the described service steps before shipping.   see questions section below  
• We offer detailed photos and videos of the instruments you buy.
• We are an approved pre-owned equipment vendor to many large US, Canadian, and EU Universities.
• We are an approved pre-owned equipment vendor to many Fortune 500 US and International Biopharma companies. 
• Technical sales consultation available
• Remote installation and instrument operation training may be available.
• On-site installation may be available in the Boston Area (New England area)
• US or International shipping is no problem (see the shipping tab on how we pack and feel at ease)

Our Guarantee

• Warranty
• You get after-sales technical support
• Customer references are available
• The instrument will be fully functional!
• Smooth process from the initial quote to order fulfillment

800# ESQ

PLEASE NOTE THAT THE QUESTIONS BELOW ARE ANSWERED IN MORE THOROUGH DETAIL ON OUR WEBSITE

Q: Can I view this instrument in person at your facility or do a live Zoom demo before it is shipped to me?

A: We can accommodate both in-person or Zoom demos.

Q: What about the warranty?

A: The instrument comes fully warranted for both parts and labor.

Q: Do you offer installation, service, etc?

A: We offer remote installation and training packages to familiarize you with this instrument.

Q: What should I watch out for when buying a used/pre-owned instrument from another lab?

A: Ensure that the instrument is in good working condition with no damage or wear that could affect its performance. Ask for details about testing steps performed, video demo, and test screenshots.

Q: Do you have more than one of these instruments on hand?

A: We generally carry multiple instruments on hand, along with a variety of spare parts.

Q: This procurement is for a University or College. Are purchase orders with NET terms accepted?

A: We accept purchase orders from all major US and Canadian universities.

Q: How fast will you ship?

A: We can ship within a few days to two weeks. Shipping time depends on the current demand for our instruments. Members of our sales team will be able to offer current delivery estimates.

Q: Will my instrument be insured during shipping?

A: Absolutely! We insure all our shipments as long as we are the shipper. If a customer ships on their account, they handle insurance.

Q: How do you pack? Have you previously packed and shipped the fragile laboratory instruments?

A: We have extensive experience shipping high-end and complex laboratory instruments in the US and Internationally.  

Q: Do you ship Internationally?

A: Yes! We have shipped to multiple continents and over 30 countries. 

Q: How much will I save buying it pre-owned, and is it worth it?

A: When compared to buying a new instrument, you will save 60% or more and have plenty of funds left over for an additional instrument or two.